 |
The Interceptor is capable of displaying the following parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display.
A sample of some of the parameters is listed below:
# RPM
# MPH
# Intake Air Temperature
# Mass Air Flow Sensor Frequency
# Mass Air Flow Sensor (lb/min.)
# Engine Coolant Temperature
# Injector Pulse Width (bank 1 and 2 if supported)
# Long Term Fuel Trim (bank 1 and 2 if supported)
# Short Term Fuel Trim (bank 1 and 2 if supported)
# O2 Sensor Voltage (bank 1 and 2 if supported)
# Manifold Pressure in PSI (Boost pressure for factory
turbo/supercharger applications)
# Ignition Advance
# Knock Retard
# Engine Run Time
# Misfire information
# Battery Voltage
# Transmission Temperature
# Transmission slip speed
# Remaining fuel
# Throttle Position Percentage
# Throttle Position Voltage
# Oil temperature
# Oil pressure (some 8 cylinder engines)
# Fuel economy (vehicle must have a MAF
# Horsepower sensor for these 2 items)
# Two user configurable analog inputs
# Fueling status (open or closed loop)
# and many more...
The Interceptor gauge is 52mm (2 1/16") in diameter and will fit in all standard gauge
pods of this size. A 5' cable is included with appropriate OBD2 connector. A splitter cable
is included with the dual Interceptor units. Gauges come with a standard black bezel or
optional anodized aluminum or chrome bezel. State bezel preference when ordering.
A function menu is available by pushing both buttons simultaneously. The first menu
option allows you to enter a record mode. Once selected, the Interceptor will return to
normal scan mode, but will start recording the displayed data automatically when the
throttle exceeds 50% and engine load exceeds 65%. Approximately 50-60 seconds of data
will be stored. Returning to the menu screen, you can choose to replay the stored data on
the Interceptor display.
Another menu option offers the ability to swap the foreground and backround colors of the
display (to be shown soon in the IMAGES section of this site). Using this feature, for
example, the gauge with a black backround and blue characters (negative image)
becomes a blue backround with black characters (positive image). Not only can this be
visually appealing but beneficial in changing lighting conditions. Positive images are
easier to read in bright sunlight, negative at night.
The Interceptor's scan rate can also be adjusted through a menu function.
DTC's (Diagnostic Trouble Codes) can be accessed and cleared via menu options. Click
here for a list of powertrain diagnostic trouble code explainations.
High intensity LEDs can be used as shift lights or warning lights to indicate when a
selected parameter exceeds an entered threshold. Due to the gauges extremely fast
update rate, this light is very accurate and easy to set. Once you try it you'll find you can't live
without it!
The Interceptor will measure 0-60 times, as well as 1/8 and 1/4 mile time and speeds.
This is accomplished through a simple menu selection. See if those mods really do work!
Finally the two analog inputs can be configured through menu choices. A linear conversion
can be entered so that an analog signal connected to the gauge can be read in appropriate
units. These inputs are handy for pressure signals such as those from MAP and oil
pressure sensors, analog outputs from Air/Fuel ratio kits, etc. These signal can then be
read and recorded along side the other parameters obtained on the vehicle's bus.
Installation is accomplished by simply plugging the supplied connector into the OBD2 port
below the steering wheel and connecting a separate included wire to a switched 12v
vehicle power source. Virtually plug-and-play!
Warranty
Aeroforce Technology Inc. warrants this product and its accessories against defects in
material and workmanship for a period of 1 year from the date of purchase.
Dual Interceptor Option: Two Interceptors can be purchased with a special splitter
cable that allows both gauges to operate simultaneously. A triple gauge set can be
purchased through special order.
Click here for the Application Guide: http://www.aeroforcetech.com/files/Aeroforce_application_guide_basic2.pdf
Customize your gauge by choosing one of the optional warning light colors: Blue, Green, Yellow, or Orange. Standard color is Red. There is a additional $20 dollar charge for the custom colors but the red comes with no extra charge.
Please allow 2-3 extra days for delivery needed to customize the gauge.
*Note: If you own of the listed vehicles below please specify year in the customer notes section:
Corvette, Silverado, Impala, Tahoe, Trailblazer, Rendevous, Ranier, Lacrosse, CTS, CTS-V, Escalade, Envoy, Sierra, Yukon, Ranier, Grand Prix, GTO |
|
|
